Weatherby Lake, MO HVAC & Plumbing Services

Completed furnace maintenance and inspection. I checked all components and amp draws. I tested airflow and temp splits. I cleaned up furnace and cleaned flame sensor. Inducer motor has 2 cracks in it and a hole. This causes an unsafe environment since exhaust can leak into the home from these openings. The pressure switch tube is dried out and cracking. With the holes found in the inducer casing and a dried and cracking pressure switch tube the systems performance could also be compromised causing the system to not run through the winter. I noticed the evaporator coil is rusted which can leak to refrigerant leaks possibly in the near future. I brought out field supervisor to provide in house confirmation on findings and help with solutions on what needs to happen from here.

L

Out today for a couple of issues after some repairs we performed. Upon arrival discovered that soap dispenser is working, their housekeeper got it functioning properly. More than likely the soap was just not loaded into the line yet. Also observed marks on tub after drain clearing and drain, still draining slowly. Upon inspection marks were merely cosmetic and wiped right off. Also removed minor amount of hair from distance between tub shoe and overflow, this improved flow significantly, however, the main issue is certainly the adapter to stop up the tub that is on the tub shoe. It is not allowing a Vortx to be created, thus draining the tub as fast as it would, although homeowner noticed a big difference in how it was draining with the adapter on. Cleaned up work area did not collect.

X

Completed furnace inspections for customer. Customer has two gas furnaces, both were tested and were within manufacturer specifications. Replaced air filters and water pads today. No recommendations at this time, both systems operating normally upon departure.

Out today to complete work as bid. Completed work successfully at this time, tested, no leaks. Cleaned up work area and collected paid with card.

Sent an additional quote for customer supplied faucets

DATE: 10/21/24 Detailed description of what was done today: arrived at home, and spoke with Nancy a call today, which was low water pressure in multiple areas in the home, as well as a tub drain that was not flowing properly. Afternoon for home inspection and fan diagnostic. We learned that the PRV that was installed had failed her in a long side of that water quality had failed on multiple remarks, causing these faucets to die early. We created a game plan” to how to fix it and presented at the homeowners. Wear and Tear: -PRV, shower, cartridge, two Lauv, Fossett, one kitchen faucet and drain line, Clarin special. After reviewing the entire house I went over everything with Nancy to ensure they understood everything going on in the house and what could be done to address it. Services done today: -Inspection Thank you for choosing LBA Services Your technician, Josiah Walker

Quoted major water pressure overhaul and filtration system

Water was getting into the inducer motor due to no drain on the exhaust. I pulled inducer motor and emptied water out. I made sure drains were open and I added a drain for the exhaust. I found no other issues and system is running as it should.

.

Went for a furnace call today. Started off with a static pressure test, it passed. Changed filter due to the old one being dirty. Did a carbon monoxide leak test with my meter, there was no leaks. After checking the heat exchanger, I found minimal rust and no cracks. Temperature split between the supply and return duct passed. Did a combustion analysis test, it passed. Blower wheel is dirty, but blower motor amps passed. Capacitor for the inducer motor passed. Exhaust flu was in good shape with no rust. Thank you for choosing LBA services!

Unable to provide a quote for replacing the floor drain because his furnace is on top of the floor drain. The branch line connecting to the floor drain is also underneath the floor drain. As of right now, the customer has no interest in a condensation pump and will use a bucket during the summer months to drain furnace and air conditioner.

Estimate

DATE 7/25/24 Detailed description of what was done today Arrived at home did for inspection and diagnostic. I seem to be in good condition, except kitchen was emitting an awful smell, so I cleaned out the disposal and P-trap’s. Homeowner also wanted the family club, but not smart AC centers. Wear and Tear: - tier, 2 disposal service After reviewing the entire house I went over everything with Connie to ensure they understood everything going on in the house and what could be done to address it. Services done today: -Cleaned kitchen disposal Thank you for choosing LBA Services Your technician, Josiah Walker

Arrived to customers for inspection. During the inspection we notice a high call on static pressure. Other than that all other components and refrigerant levels met factory specs.

Static is failing at 1.0 on a .5 max system. Acfm count failed as well. Recommend shutting off system. Customers just want to make sure refrigerant is good to go and is selling the home.

Arrived at the customers house to put on a cap on the refrigerant line. The cap that is needed is not stocked on the service vans. Someone will be out tomorrow morning to put the cap on.

Checked all operations in the cooling mode and inspected the furnace filter. Checked the static pressure and found it was passing at this time. Checked all electrical and refrigerant components in the system. Today we found the capacitor was failing and the contactor was burnt. Upon customer approval we replaced both components and got them on the new family club.

Arrived for ac maintenance. Static pressure failed. Blower wheel clean. All electronics in ac and furnace within range. Temp split good. Outside coil dirty. Refrigerant levels good. Cleaned outside coil -Ren

Air Conditioning System Repairs: Upon diagnosing frequent system shutdowns, we conducted a comprehensive inspection and identified electrical component failure, particularly in the capacitor. Swiftly replacing the defective capacitor with a high-quality replacement ensured consistent power supply and system stability. Additionally, we performed rigorous electrical testing to verify proper functionality and prevent future breakdowns, guaranteeing uninterrupted comfort and reliability for the client.

Unit was slightly low on charge. Added correct amount. All components were working at current time. Condenser fan may have short causing unit to over heat. No current problems at this time.

Estimate

Static quote

Arrived for no cool call. Found static was failing on the system. She agreed for a field supervisor to come out. Found a leak in a schrader core on line set. System was out of refrigerant. Also found the blower wheel was dirty and needed to be cleaned. Replaced the schrader valve. She agreed to refill with refrigerant. System is on and running.