Belton, MO HVAC & Plumbing Services

Installed new blower motor and decrease fan speed. Tested system four times to make sure it works.

Delivered two space heaters

Estimate

Upon arrival I found the system was not heating. After inspection I found that there is a wiring short to the blower motor causing it to turn on and off at random. This unit needs a new ECM blower motor w/module. We will order Monday morning and get back out to install as well. If you have any questions or concerns please feel free to call us! Your LBA Technician, Tyler Rickard P.S. No payment was due for todays visit. Happy New Year!

Installed new ductwork, humidifier and uv light

We will be installing a humidifier redirecting the drain line, installing a UV and germicidal unit and redoing the ductwork in and out of the system to ensure that we get 2000 CFM on both sides

system out, no air circulating nothing is coming on, steady red light on April air system

Picked up tools

For this job, I was showing up on the call for no hear. Upon checking the system I immediately noticed that it was short cycling and was giving me two separate error codes One was for thermal overload and the second one was for pressure switch error. After checking the inducer, I checked the heat exchanger. He is changer was damaged with holes and cracks in multiple areas, causing it to lose suction and also overheat. After Calling Amana to see about warranty information, it was clear that the soonest they would be able to get exchanger manufactured was over a month. because of this LBA offered to install a furnace cost for under $1000 more than the heat exchanger. Probably the best option moving forward. Otherwise we will have to wait for a Amana to produce a heat exchanger

Reset thermostat reminder for filter.

Out for furnace not working and displaying error code.

Customer cancelled. Replaced with AB May

Sale

Arrived for furnace maintenance today. Started by checking static pressure and found it is failing. A field supervisor is out to discuss further. Carbon monoxide test was 0ppm. Heat exchanger is looking good. Blower wheel is picking up dust and should be cleaned soon. All electrical components are running properly at this time. The main issue is the failed static and the affects it can have on a system. System is running upon leaving. Thanks for choosing LBA.

X

Went for a maintenance call today. When going to air handler. Temp split is passing. Heat strips are passing as well as blower motor amperage. Did notice capacitor is failing for system. Did recommend for replacement. Customer declined at this time. Condenser is passing in refrigerant and electrical components. Did notice duct work could use a clean as well. Since filter was collecting a lot of dust on filter for only a month. No further wear and tear. Thank you for choosing LBA services-Johann.

Sales

Arrived for furnace maintenance today. Checked static pressure and found it is passing today. Carbon monoxide test was 0 ppm. Heat exchanger has no rust or cracks. All electrical components are running properly at this time. There’s a good temp split between supply and return air. System is running upon departure. Thanks for choosing LBA.

12/2/24. Stopped into Trane after calling multiple times and was able to order a warranty valve in. The part had to be matched. There is some concern about the valve number not matching, It cross referenced Arrival time for the part will be updated tomorrow when it is available.

Arrived to do a performance maintenance. Set system to run and the heat pump started up and ran. Measured a temperature split and static pressure. Found that the system is operating with failing static pressure. Spoke with homeowner about the system and they declined finishing the diagnosis on the systems static pressure. Switched system over to gas heat. Set up for combustion analysis. Verified operation of all mechanical and electronic components in the furnace. Cleaned the flame sensor and retested its performance. Checked blower for cleanliness and to see if there is any play in the bearings. Found that the blower wheel was very dirty and was hastily cleaned. Checked systems heat exchanger to ensure proper venting of flue gas. Found that the heat exchanger was heavily coated in dust debris. Checked for carbon monoxide in the air stream. Performed an electronic gas leak search. Spoke with homeowner about the system. Furnace is operational at this time.

Sales

Follow up

Remove old frost proof hose bib and install new

Sold his bib for Tuesday morning. Also gave estimate for replacing main shut off valve. He will review estimate and possibly approve tomorrow. Cleaned up work area. Will gather parts in the morning and complete. Estimate has been Eastside and will be charging card on file.

Estimate